HEAT YOUR HOME FREE
Atomic Hydrogen Aphoid Furnace Design
You might be interested in this research.
In 1926 Dr. Irving Langmuir discovered an anomaly:
When hydrogen is passed through an electric arc it is converted from molecular Hydrogen to H1 or atomic hydrogen.
Atomic hydrogen has unusual properties.
When it is ignited and the flame directed against a catalytic metal an enormous amount of heat is liberated as the H1 hydrogen converts back to H2 (molecular hydrogen).
The source of this excess energy has not been explained by current scientific theories however scientists like Maxwell and inventors like Nikola Tesla believe that it is drawn from Zero Point Energy, ZPE.
The Zero Point Radiation field was discovered by Dutch physicist M.J. Spamaay during the 1920′s.
The atomic hydrogen process was first discovered by a scientist, Dr. Irving Langmuir in 1926. See http://www.lateralscience.co.uk/AtomicH/atomicH.html for details.
Since modern science doesn’t acknowledge the existence of ZPR much of the research of Langmuir showing over-unity power production has been ignored (or repressed) for over eighty years. Yet, as you will see, Dr. Langmuir and later scientists have proven that the process of generating atomic hydrogen and catalyzing it back to H2 (molecular hydrogen) results in an energy gain over 800 times beyond the measured input energy.
Another inventor built and patented an atomic hydrogen welding torch (1933) based on his discovery that when Oxygen is passed through the electric arc along with the Hydrogen a number of complex chemical reactions result.
Flame temperature can reach 4000 degrees Centigrade or higher.
That’s hot enough to melt tungsten. Surprisingly, the mixture doesn’t explode as it passes through the arc. While the atomic hydrogen flame is hot enough to burn through firebrick the tip of the torch itself is just warm to the touch.
Enormous energy is released in the form of heat that exceeds the expected amount of burning H2 in air by about 853 times. This factor of 853 times more energy is doubled when Oxygen is passed through the arc at the same time. Thus:
H.sub.2.fwdarw.H+H absorbing 101,000 cal.per gram mole
O.sub.2.fwdarw.O+O absorbing 117,000 cal.per gram mole
total 218,000 cal.per gram mole.
As I said, the heat energy released exceeds the expected energy from both the electrical energy of the arc plus the combustion energy of H2 by at least 850 times not even counting
the Oxygen effect.
I’ve built a prototype Atomic Hydrogen furnace/boiler based on this concept that is close to completion.
The unit injects HHO through an electric arc within an air tight combustion chamber and boiler. The atomic hydrogen flame contacts a Stainless Steel sodium filled heat reservoir, (catalytic cylinder). This heat sink cylinder is wrapped with
multiple layers of high pressure/high temperature copper tubing. The hot hydrogen gases pass over and around the coils. A high pressure pump (actually a diesel injection pump) keeps the coils filled with extremely hot water at high pressure. This configuration is called a Flash Boiler.
When one of the cylinders of the steam engine requires a charge of steam the high pressure injector injects a tiny amount of superheated water into the cylinder.
Because there is a pressure drop between the water and the cylinder the water immediately "flashes" into superheated steam.
Since the cylinder walls of the steam engine are maintained at a high temperature any water droplets that fail to "flash" into
steam are exploded outward by the steam.
These minute water droplets are forced against the hot cylinder walls
where they also expand into superheated steam driving the piston. A
water droplet expands 1650 times the original volume when it flashes
to the steam state.
There are several advantages to using flash steam.
1.The quantity of water injected at each stroke is far
smaller than the volume of steam passing the inlet valve in an engine
served by a mono-tube generator (steam at atmospheric
pressure occupies about 1650 times the volume of water).
This tiny quantity of water is simply much easier to
dispense through an injector than the much larger volume of steam
which an inlet valve must admit in a mono-tube engine.
2. – Advantage #2 is speed. Such a small quantity of
water may be dispensed at speeds equal to those found in diesel
injection systems, whereas steam which has to negotiate an inlet valve
is seriously impeded if the engine is pushed to higher speeds by a
phenomenon known to steam engineers as ‘wire-drawing’.
The speed advantage allows an automobile steam engine
to operate more efficiently and at higher RPM.
3. Efficiency. The Flash boiler design can be more compact and has fewer thermodynamic losses since the steam is not stored or transported. Instead, it is injected directly into the steam engine’s cylinders in the form of a minute amount of water. Since the steam engine’s expansion chambers are maintained at a high temperature
the steam continues to heat and expand doing more work in less space.
Water entering the cylinder immediately converts to superheated steam. The steam
powers the pistons – see below: target=Dscf71064cylweb.jpg”
Green Steam Engine has steam engine designs that have been built and tested. These steam engines are highly efficient, low cost to build yet can be designed for up to 500 horse power. A small, 20 HP
unit could provide all the electrical needs for the average home when
coupled to the appropriately sized generator.
According to the research of Langmuir and others once the Atomic Hydrogen reacts with the catalyst it reverts to H2. It is not
consumed* but merely acts as an energy transfer medium. It is
entirely possible that the molecular hydrogen, H2, can be pumped back through the system or recycled.
It is also important to note that the electrolysis process (or the Stanley Meyer Water Fuel Cell design) creates atomic
Hydrogen and Oxygen.
At any rate, the spent superheated steam can be used to provide heating for a domestic hot water tank
as well as for hot water/baseboard home heating. When the steam condenses it is recirculated through the boiler.
Since the unit is expected to put out at least 800 times the energy as the electric input required to power the HHO
generator and to create the arc this device should sustain operation
with no external power source (once the process is started).
*Based on the
reporting of William Lyne and the research of Langmuir and others the Hydrogen is not consumed in this process. William Lyne in his book Occult Ether Physics, reports that the atomic hydrogen merely
reverts back to H2, molecular hydrogen and can be recycled. Of course, the combustion of hydrogen in whatever form results in water. So, this is a completely pollution free over-unity source of energy. Use of this technology in households would create complete energy independence liberating mankind from the stranglehold of the fossil fuel cartel.
Possible Research Avenue
When H2O is exposed to extreme heat the water
spontaneously breaks down into it’s component gases…Hydrogen and
Oxygen. Of all metals in pure form, tungsten has the highest melting
point (3,422 °C,
Since the flame is sufficiently hot to melt tungsten it is entirely possible that minute amounts of water injected at the point of combustion will break down into HHO gas. Some scientists believe the flame of an atomic torch exceeds 4000 °C.
An HHO generator provides the HHO (hydrogen/oxygen gas) to fuel the boiler. The steam powers a steam engine that can power a generator to provide household electricity.
The expired steam can be condensed back into water by passing through a hot water tank providing hot water for household heating and hot water
needs. Once the steam is condensed it is pumped back into the boiler.
Ultimately, this unit could provide an extremely efficient source of electric power that coupled with storage batteries
could power a vehicle with zero emissions or a ZEV (zero emissions vehicle}.
I believe that a complete home heating and power unit can be profitably built to be sold at retail for approximately $25,000.
If this sounds high remember that this power plant will liberate the
homeowner from the grid. No more electricity or oil bills forever!
I’m interested in working with any company with experience in
electronics, mechanical engineering, plumbing/heating, machining and the building trades.
If you are qualified and interested in the possibility of becoming a
dealer/installer please complete the form:
or Call Phone: 866-375-6941
Atomic Hydrogen Process is 100% CLEAN and SAFE.
"When you add the fact that the hydrogen is not consumed in the “burning” process, and can thus be recycled, it should become very clear to any scientist, humanist, environmentalist, business executive
and indeed to every human being that is concerned about the state of
our wonderful planet, that no more time should be wasted. The time has
come for removing the responsibility of defining the energy policies and structures of the future from the hands of the established energy
industries, and place it in the hands of men of science who will work
for the preservation of the environment that sustains all life on
Earth. Men who will work for the economic development of the third world by means of providing clean, abundant and inexpensive energy
Such an initiative will only succeed when massively supported by the visionary captains of industry who will have the courage to dismantle the
existing and scandalous energy grid which now envelopes our planet, by investing in the production and marketing of small energy generators for individual households, factories, transport etc.
Once such a generator has been acquired by the consumer, his further energy requirements will be covered for FREE, giving him independence in terms of energy as well as increased buying power for any other
economic development." Nicholas Moller
334 Lowell Town Road Wiscasset, Maine 04578